Description
Features:
1. The radio is built on the DSR principle - the function is determined by the loaded software
2. 50 kHz to 250 MH and 400 MHz to 2 GHz (registered upgrade)
3. All types of analog modulation. AM/SSB/NFM/WFM
4. Powerful. variable filter width, adaptive noise suppressor, threshold noise suppressor, Noise Blanker (AGC_Equalizer
5. Multi-function chip msi001
6. stm32h743 with powerful functions of clock frequency 480Mhz
7. 3.5-inch IPS touch-capable large display
8. Built-in UHF storage
9. Controls - 2 encoders with buttons and touchscreen
10. Power supply is powered/charged by external TYPE-C interface, built-in 2500MA lithium battery
12. Connect to computer via USB, can transmit CAT, IQ and audio
13.160Khz span, with scalability
14. Sensitivity up to 200Mhz, 0.3uv=10dB at S/W
15. Due to the characteristics of the msi001 chip, the dynamic resistance range is about 85dB
16. With backlight control
17. SMA antenna female socket
Register the upgraded version to widen the frequency and add functions such as CW decoding
Simple operation instructions:
1.?HARD (setting): EN1, EN2: The direction of addition and subtraction of the two encoders is reversed. V bat/power display: S standard, L low voltage. SW ante/shortwave antenna selection: 50ohm 50ohm/Hi-z high impedance. ATT attenuator: the same as the transceiver. LNA/MIX, MIX GR: Do not open the functions that the current machine (including the original version) does not have, otherwise the gain and sensitivity will be greatly reduced! RF GAIN/RF gain: The same as the transceiver, when it is set at about 20, the sensitivity is the best. PREAMP/Pre-amplifier: Same as transceiver. F correct/frequency correction: Use as needed. Sm correct/S table correction: Use as needed.
Time setting: Press and hold HARD to enter the time setting, then press the volume encoder to increase or decrease the number, and press inward to switch. When done, press and hold the encoder and release it when a "beep" sound is heard.
2.?AUDIO (audio): NB/spark noise Thes/start control value and Config/setting value; I have always set these two to 2, you can try it yourself. NB/Switch: Dis on/Ena off. AGC/Auto Gain Control. AGC LIN/AGC peak: experimental adjustment. MANUAL/MANUAL CONTROL: Experimental adjustment. AGC MODE/AGC Mode: Relevant, Fast, Normal, Slow, Very Slow. EQ (Equalizer) EQ TYPE/Equalizer switch and selection: click first, then use the volume encoder to open and select; there are light music, live, club, rock, bass, jazz, pop, language. WFM Stereo/FM Stereo: Headphones only. NR/DSP Noise Reduction Thes/Setting Value: Set according to the sense of hearing. SQL Thes/settings. SQL switch.
3.?VISUAL (screen effect) BRIGHT MIN/minimum brightness: 20. BRIGHT MAX/Maximum brightness: 100. REDUCT TIME/Reduce time: 0 sec/0 seconds. SLEEP TIME/Sleep time: 300 sec/sec. LCD SLEEP/Backlight sleep switch: D/On, E/Off. FFT ave/spectral averaging speed: 50. FFT scale/spectrum display range: 50. FFT color/spectral color: four. Pan percent/spectral pan %: 70. WTF delay/spectral reflection delay: 0. WTF Gain/Spectrum reflection gain: 0dB. FFT fill/spectral fill: D/On, E/Off.
4. MODE is the same as that of the transceiver, and its Decoder is a CW decoding switch. After opening, under the frequency, there is a small white bar. After opening, "Min SNR/Minimum Level" appears: adjust as needed to make decoding more accurate.
5. BAND (Band) Band key, you can switch the band, but also memory selection. The memory is divided into 5 pages, 10 per page; it can be arbitrarily stored in a certain memory. for invocation. When storing, first adjust the frequency, mode, step, AGC, RF Gain, FLT parameters, PRE and other data, then select the storage page and location, long press the memory box with your finger, and release it after hearing the "beep" sound. .
6. Select frequency step: Press the frequency knob to switch to step mode, and then use the frequency knob to adjust as needed. The minimum step is 10Hz, and the maximum is 30KHz.
Package included:
1 x Set of SDR Receiver (with Aluminum Alloy Shell)
1 x USB Cable
1 x Antenna (SMA to M seat)
Delivery:
Free & Fast Shipping
Delivery Time: 2-8 Working Days
Warranty:
Warranty Period: 1 Years
Returns: The buyer have right to return the item within 60 days after the receipt of the product.24-Hour Online Service: If you need more helps, we are here for you.
1. The radio is built on the DSR principle - the function is determined by the loaded software
2. 50 kHz to 250 MH and 400 MHz to 2 GHz (registered upgrade)
3. All types of analog modulation. AM/SSB/NFM/WFM
4. Powerful. variable filter width, adaptive noise suppressor, threshold noise suppressor, Noise Blanker (AGC_Equalizer
5. Multi-function chip msi001
6. stm32h743 with powerful functions of clock frequency 480Mhz
7. 3.5-inch IPS touch-capable large display
8. Built-in UHF storage
9. Controls - 2 encoders with buttons and touchscreen
10. Power supply is powered/charged by external TYPE-C interface, built-in 2500MA lithium battery
12. Connect to computer via USB, can transmit CAT, IQ and audio
13.160Khz span, with scalability
14. Sensitivity up to 200Mhz, 0.3uv=10dB at S/W
15. Due to the characteristics of the msi001 chip, the dynamic resistance range is about 85dB
16. With backlight control
17. SMA antenna female socket
Register the upgraded version to widen the frequency and add functions such as CW decoding
Simple operation instructions:
1.?HARD (setting): EN1, EN2: The direction of addition and subtraction of the two encoders is reversed. V bat/power display: S standard, L low voltage. SW ante/shortwave antenna selection: 50ohm 50ohm/Hi-z high impedance. ATT attenuator: the same as the transceiver. LNA/MIX, MIX GR: Do not open the functions that the current machine (including the original version) does not have, otherwise the gain and sensitivity will be greatly reduced! RF GAIN/RF gain: The same as the transceiver, when it is set at about 20, the sensitivity is the best. PREAMP/Pre-amplifier: Same as transceiver. F correct/frequency correction: Use as needed. Sm correct/S table correction: Use as needed.
Time setting: Press and hold HARD to enter the time setting, then press the volume encoder to increase or decrease the number, and press inward to switch. When done, press and hold the encoder and release it when a "beep" sound is heard.
2.?AUDIO (audio): NB/spark noise Thes/start control value and Config/setting value; I have always set these two to 2, you can try it yourself. NB/Switch: Dis on/Ena off. AGC/Auto Gain Control. AGC LIN/AGC peak: experimental adjustment. MANUAL/MANUAL CONTROL: Experimental adjustment. AGC MODE/AGC Mode: Relevant, Fast, Normal, Slow, Very Slow. EQ (Equalizer) EQ TYPE/Equalizer switch and selection: click first, then use the volume encoder to open and select; there are light music, live, club, rock, bass, jazz, pop, language. WFM Stereo/FM Stereo: Headphones only. NR/DSP Noise Reduction Thes/Setting Value: Set according to the sense of hearing. SQL Thes/settings. SQL switch.
3.?VISUAL (screen effect) BRIGHT MIN/minimum brightness: 20. BRIGHT MAX/Maximum brightness: 100. REDUCT TIME/Reduce time: 0 sec/0 seconds. SLEEP TIME/Sleep time: 300 sec/sec. LCD SLEEP/Backlight sleep switch: D/On, E/Off. FFT ave/spectral averaging speed: 50. FFT scale/spectrum display range: 50. FFT color/spectral color: four. Pan percent/spectral pan %: 70. WTF delay/spectral reflection delay: 0. WTF Gain/Spectrum reflection gain: 0dB. FFT fill/spectral fill: D/On, E/Off.
4. MODE is the same as that of the transceiver, and its Decoder is a CW decoding switch. After opening, under the frequency, there is a small white bar. After opening, "Min SNR/Minimum Level" appears: adjust as needed to make decoding more accurate.
5. BAND (Band) Band key, you can switch the band, but also memory selection. The memory is divided into 5 pages, 10 per page; it can be arbitrarily stored in a certain memory. for invocation. When storing, first adjust the frequency, mode, step, AGC, RF Gain, FLT parameters, PRE and other data, then select the storage page and location, long press the memory box with your finger, and release it after hearing the "beep" sound. .
6. Select frequency step: Press the frequency knob to switch to step mode, and then use the frequency knob to adjust as needed. The minimum step is 10Hz, and the maximum is 30KHz.
Package included:
1 x Set of SDR Receiver (with Aluminum Alloy Shell)
1 x USB Cable
1 x Antenna (SMA to M seat)
Delivery:
Free & Fast Shipping
Delivery Time: 2-8 Working Days
Warranty:
Warranty Period: 1 Years
Returns: The buyer have right to return the item within 60 days after the receipt of the product.24-Hour Online Service: If you need more helps, we are here for you.